帮我寻找一下液下渣浆泵型号A武安液下渣浆泵型号

使轴承组件先向前移动，使叶轮与前护套接触 再使轴承组件向后移动，使叶轮与后护套接触，测出轴承组件总的移动距离，取此距离的一半作为叶轮与前后护套的间隙，再通过调整螺栓调节轴承组件的位置，保证叶轮与前后护套的正确间隙值 调整后，在再次起动前，必须重新检查叶轮转动是否正常 轴承组件压紧螺栓与调整螺栓是否拧紧，然后再起动泵。

一、产品概述SP液下渣浆泵为立式离心液下渣浆泵，浸入液下，用于输送磨蚀性、粗颗粒、高浓度渣浆。不需要任何轴封和轴封水，在吸入量不足的工况下也能正常工作。

SP型液下渣浆泵过流部件由耐磨金属制成。 

根据渣浆池液面的高低，可选择不同长度的泵传动轴或吸入管。 

采用多种速度和多种变型方式，使得泵在最佳工况下运行，使用寿命长，运行效益高，能满足多类恶劣的输送条件。 

Second, SP liquid slurry pump application Range 
Slurry pump is mainly suitable for conveying corrosive, coarse particles, high concentration slag slurry. Widely used in metallurgy, mining, coal, electricity, building materials, environmental protection and other departments.
Third, SP liquid slag slurry pump structure description 
The difference between the slurry pump structure of SPR liquid and the slurry pump under SP liquid is only that the parts of the dipping slag slurry are lined with corrosion-resistant rubber, the parts lined with rubber include shafts, pumps, impellers, protective plates and filters, and the connecting bolts in the lower part of the immersion liquid are equipped with rubber protective sleeves, and the transmission parts and SP pumps
SP Liquid slurry pump pump body, impeller guard plate are made of wear-resistant materials. The pump end of the bearing body adopts a double row tapered roller bearing, and the driving end adopts a single row cylindrical roller bearing, which can withstand the maximum axial load of the pump. The bearing body is fitted with a motor seat or motor bracket, which can be driven by a direct or triangle belt drive. The pump should be immersed in the slurry pool to work, the pump body suction inlet with a filter, can prevent large particles into the human pump. Jdhuiquan5.15
Four, the depth of the liquid can be extended pump self-belt liquid depth of about 70cm, according to customer requirements to increase the depth of the liquid, (the price with the addition of a long number of meters and different) please customers and customer service personnel in advance to explain.

帮我寻找一下液下渣浆泵型号A武安液下渣浆泵型号

5，装好联接管，固定盘，后盖，叶轮，泵体，弯管与出水管并固定。注：叶轮与泵壳前端间隙为2～2.5mm。6，装上电机座与含有电联的电机；即完成整泵的装配过程。7，泵的拆卸按上述相反步骤进行。渣浆泵安装和拆卸一定要按照遵守机械的安装步骤，以防止泵在使用过程中出现故障造成不必要的损失，缩短泵的适用寿命。

五、型号意义

    40 PV-SP

   40----------吐出口径40mm

   PV--------- PV型轴承组件

   SP----------液下泵

水泵安装

 泵安装的好坏对泵的运行和寿命冇重要影响，所以安装和校正必须仔细进行。泵的外形及安装尺寸。