搜一搜液下抽沙泵图片A临漳液下抽沙泵图片
搜一搜液下抽沙泵图片A临漳液下抽沙泵图片
产品价格:¥2980(人民币)
  • 规格:完善
  • 发货地:河北
  • 品牌:
  • 最小起订量:1台
  • 诚信商家
    会员级别:标准会员
    认证类型:企业认证
    企业证件:通过认证

    商铺名称:河北会泉泵业有限公司

    联系人:徐经理(先生)

    联系手机:

    固定电话:

    企业邮箱:1815991877@qq.com

    联系地址:河北省石家庄市桥西

    邮编:5000

    联系我时,请说是在汽配名企网上看到的,谢谢!

    商品详情

      搜一搜液下抽沙泵图片A临漳液下抽沙泵图片

      轴封型式的选择渣浆泵主要有填料密封,副叶轮密封和机械密封等轴封形式。副叶轮密封一般在倒灌工作下使用,高管压力应小于10%泵出口压力,这种轴封型式不加轴封水,但使用副叶轮密封降增加功率消耗,一般为额定功率的5%左右。填料密封需加轴封水,并保证足够的水压和水量,轴封水压等于泵出口压力加机械密封需加轴封水,密封性好,无泄漏。

      一、产品概述SP液下渣浆泵为立式离心液下渣浆泵,浸入液下,用于输送磨蚀性、粗颗粒、高浓度渣浆。不需要任何轴封和轴封水,在吸入量不足的工况下也能正常工作。

      SP型液下渣浆泵过流部件由耐磨金属制成。 

      根据渣浆池液面的高低,可选择不同长度的泵传动轴或吸入管。 

      采用多种速度和多种变型方式,使得泵在最佳工况下运行,使用寿命长,运行效益高,能满足多类恶劣的输送条件。 

      搜一搜液下抽沙泵图片A临漳液下抽沙泵图片

      Second, SP liquid slurry pump application Range 
      Slurry pump is mainly suitable for conveying corrosive, coarse particles, high concentration slag slurry. Widely used in metallurgy, mining, coal, electricity, building materials, environmental protection and other departments.
      Third, SP liquid slag slurry pump structure description 
      The difference between the slurry pump structure of SPR liquid and the slurry pump under SP liquid is only that the parts of the dipping slag slurry are lined with corrosion-resistant rubber, the parts lined with rubber include shafts, pumps, impellers, protective plates and filters, and the connecting bolts in the lower part of the immersion liquid are equipped with rubber protective sleeves, and the transmission parts and SP pumps
      SP Liquid slurry pump pump body, impeller guard plate are made of wear-resistant materials. The pump end of the bearing body adopts a double row tapered roller bearing, and the driving end adopts a single row cylindrical roller bearing, which can withstand the maximum axial load of the pump. The bearing body is fitted with a motor seat or motor bracket, which can be driven by a direct or triangle belt drive. The pump should be immersed in the slurry pool to work, the pump body suction inlet with a filter, can prevent large particles into the human pump. Jdhuiquan5.15
      Four, the depth of the liquid can be extended pump self-belt liquid depth of about 70cm, according to customer requirements to increase the depth of the liquid, (the price with the addition of a long number of meters and different) please customers and customer service personnel in advance to explain.

      搜一搜液下抽沙泵图片A临漳液下抽沙泵图片

      搜一搜液下抽沙泵图片A临漳液下抽沙泵图片

      使轴承组件先向前移动,使叶轮与前护套接触 再使轴承组件向后移动,使叶轮与后护套接触,测出轴承组件总的移动距离,取此距离的一半作为叶轮与前后护套的间隙,再通过调整螺栓调节轴承组件的位置,保证叶轮与前后护套的正确间隙值 调整后,在再次起动前,必须重新检查叶轮转动是否正常 轴承组件压紧螺栓与调整螺栓是否拧紧,然后再起动泵。

      搜一搜液下抽沙泵图片A临漳液下抽沙泵图片

      五、型号意义

          40 PV-SP

         40----------吐出口径40mm

         PV--------- PV型轴承组件

         SP----------液下泵

      水泵安装

       泵安装的好坏对泵的运行和寿命冇重要影响,所以安装和校正必须仔细进行。泵的外形及安装尺寸。

       1、安装和校正:
      1) 清除底座上的油腻和污垢,把底座放在地基上。
      2) 用水平仪检查底座的水平度,允许用楔铁找平。
      3) 用水泥浇灌底座和地脚螺栓孔眼。
      4) 水泥干固后应检查底座和地脚螺栓孔眼是否松动,合适后拧紧地脚螺栓,重新检查水平度。
      5) 清理底座的支持平面,水泵脚及电机脚的平面,并把水录和电机安装到底座上去。
      6) 联轴器之间应保持一定的间隙,检查水泵轴和电机轴中心线是否一致,可用薄垫片调整使其同心。
      测量联轴器的外园上下,左右的差刖不得超过0.1mm,两联轴器端面间隙一周上最大和最小的间咪差别不得超过0.3(mm
      2、安装说明:
      1) 泵的安装高度,管路的长度.直径、流速应符合计算,力求减少不必要的损失。
      2) 长距输送时应取较大的管径,泵的管路应有自己的支架,不允件管路的重量加在泵上,避免把泵压坏。
      3) 排出管路如装逆止阀应装在闸阀的外面。
       离心泵,自吸泵,蝶阀等。公司自兴办以来,一向专注于产品立异与开发,为了跋涉产品的层次,完善产品的售后效能,和谐,猛进,凯泉人愿和新老朋友携手共进,创始美好未来……河北会泉泵业有限公司是一家集研制,制作,出售,效能于一体的泵阀企业。主导水泵产品有耐腐蚀泵,排污泵,隔膜泵,螺杆泵。务实尚德磁力泵。咱们本着诚信运营的准则,生动跋涉,勇于开荒,经过多年的竭力,使上诚的产品深受石油,化工,电力,造纸,环保,冶金,煤矿,食物,给排水工程用户的一起好评。会泉公司全面选用ISO2000《质量处理体系要求》,并有用的施行,自兴办以来一向把质量处理作为榜首寻求政策,发扬精力,争创一流的精力在泵阀作业中不断翻开强健。
    在线询盘/留言
  • 0571-87774297