查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案
查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案
产品价格:¥2980(人民币)
  • 规格:完善
  • 发货地:河北
  • 品牌:
  • 最小起订量:1台
  • 诚信商家
    会员级别:标准会员
    认证类型:企业认证
    企业证件:通过认证

    商铺名称:河北会泉泵业有限公司

    联系人:徐经理(先生)

    联系手机:

    固定电话:

    企业邮箱:1815991877@qq.com

    联系地址:河北省石家庄市桥西

    邮编:5000

    联系我时,请说是在汽配名企网上看到的,谢谢!

    商品详情

      查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案

      铬27耐磨铸铁抗磨蚀性类似硬镍1#,就碱性混合液而言,具有较好的耐腐蚀性,价格高于硬镍1#,Cr15Mo3是目前世界上公认的优良抗磨蚀材质,宏观硬度高达布氏硬度对粗颗粒强磨蚀浆体有较好的抗磨蚀性能,但价格较高,且较脆。

      一、产品概述SP液下渣浆泵为立式离心液下渣浆泵,浸入液下,用于输送磨蚀性、粗颗粒、高浓度渣浆。不需要任何轴封和轴封水,在吸入量不足的工况下也能正常工作。

      SP型液下渣浆泵过流部件由耐磨金属制成。 

      根据渣浆池液面的高低,可选择不同长度的泵传动轴或吸入管。 

      采用多种速度和多种变型方式,使得泵在最佳工况下运行,使用寿命长,运行效益高,能满足多类恶劣的输送条件。 

      查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案

      Second, SP liquid slurry pump application Range 
      Slurry pump is mainly suitable for conveying corrosive, coarse particles, high concentration slag slurry. Widely used in metallurgy, mining, coal, electricity, building materials, environmental protection and other departments.
      Third, SP liquid slag slurry pump structure description 
      The difference between the slurry pump structure of SPR liquid and the slurry pump under SP liquid is only that the parts of the dipping slag slurry are lined with corrosion-resistant rubber, the parts lined with rubber include shafts, pumps, impellers, protective plates and filters, and the connecting bolts in the lower part of the immersion liquid are equipped with rubber protective sleeves, and the transmission parts and SP pumps
      SP Liquid slurry pump pump body, impeller guard plate are made of wear-resistant materials. The pump end of the bearing body adopts a double row tapered roller bearing, and the driving end adopts a single row cylindrical roller bearing, which can withstand the maximum axial load of the pump. The bearing body is fitted with a motor seat or motor bracket, which can be driven by a direct or triangle belt drive. The pump should be immersed in the slurry pool to work, the pump body suction inlet with a filter, can prevent large particles into the human pump. Jdhuiquan5.15
      Four, the depth of the liquid can be extended pump self-belt liquid depth of about 70cm, according to customer requirements to increase the depth of the liquid, (the price with the addition of a long number of meters and different) please customers and customer service personnel in advance to explain.

      查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案

      查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案

      4,拆下中部支架,拉下联轴器。5,拆下轴承体上下轴承盖,即可检讨轴承状况。二,液下泵的起动,泊车和工作需要1,液下泵电机在未设备前,应接通电源检讨改变偏向,必需与泵的规矩改变偏向一致2,液下泵装上电机,渣浆泵报价盘动联轴器,检讨泵轴与电机能否同心,改变能否轻重不匀,正常后再工作。

      查一查液下渣浆泵安装方案A昌黎液下渣浆泵安装方案

      五、型号意义

          40 PV-SP

         40----------吐出口径40mm

         PV--------- PV型轴承组件

         SP----------液下泵

      水泵安装

       泵安装的好坏对泵的运行和寿命冇重要影响,所以安装和校正必须仔细进行。泵的外形及安装尺寸。

       1、安装和校正:
      1) 清除底座上的油腻和污垢,把底座放在地基上。
      2) 用水平仪检查底座的水平度,允许用楔铁找平。
      3) 用水泥浇灌底座和地脚螺栓孔眼。
      4) 水泥干固后应检查底座和地脚螺栓孔眼是否松动,合适后拧紧地脚螺栓,重新检查水平度。
      5) 清理底座的支持平面,水泵脚及电机脚的平面,并把水录和电机安装到底座上去。
      6) 联轴器之间应保持一定的间隙,检查水泵轴和电机轴中心线是否一致,可用薄垫片调整使其同心。
      测量联轴器的外园上下,左右的差刖不得超过0.1mm,两联轴器端面间隙一周上最大和最小的间咪差别不得超过0.3(mm
      2、安装说明:
      1) 泵的安装高度,管路的长度.直径、流速应符合计算,力求减少不必要的损失。
      2) 长距输送时应取较大的管径,泵的管路应有自己的支架,不允件管路的重量加在泵上,避免把泵压坏。
      3) 排出管路如装逆止阀应装在闸阀的外面。
       ZL,ZLB(ZLDB)系列轴流泵,IS,ISW,ISG系列离心泵,XA系列离心泵,S(SH),SA系列离心泵,QZ,QH(QSH)系列潜水泵,SZ。HL系列混流泵现在我公司首要产品有:HW(HBC)SZG系列水环式真空泵,BPZ,TC,NS系列自吸泵,DTE系列离心泵,各种固定式,移动式柴油机械电动抗旱,排涝机组。检测方法完全,其水泵产品的功用参数和零部件的制作精度都经国内作业部分供认的检测安排检测合格的产品,先后取得了出产许可证。工艺装备精巧我公司具有多年出产制作水泵的经历农机推行证和出口产质量量许可证。在商场以远销,中东,非洲,东南亚等二十多个和区域,并赢得了客户的一起好评。“产质量量过硬。
    在线询盘/留言
  • 0571-87774297