:新余广柴服务
HM813849/10 HM813810 HM813849 HM218248/10 HM218248 HM218210 31314 31308 30312 30214 A4138D A4059 94800/98789D 9380 90016 64700D 71451D 71450 39580 39520 30208M 30205XL 31308 6580 6535 6580/35 3877 3820 3877/20 HP16010 ER-12 ER12 JP16049 417520 28523/28520-20024 46790/46720 JM207PP-PR JM207PPPRJM714249 JM714210 SMN114K SN107K GN211KRRB+P座 GN111KRRB+T18802 170RU51R3 YAS-40 DODGE轴承 P4B-S2-115R (070361) DODGE轴承 P4B-S2-200R (070362) DODGE轴承 P4B-S2-203R (070363) DODGE轴承 P4B-S2-207R (070365) DODGE轴承 P4B-S2-211R (070367) DODGE轴承 P4B-S2-215R (070368) DODGE轴承 P4B-S2-300R (070369) DODGE轴承 P4B-S2-307R (070371) DODGE轴承 P4B-S2-315R (070373) DODGE轴承 P4B-S2-407R (070375) DODGE轴承 P4B-S2-415R (070377) DODGE轴承 P4B-S2-115RE (070379) DODGE轴承 P4B-S2-200RE (070380) DODGE轴承 P4B-S2-203RE (070381) DODGE轴承 P4B-S2-207RE (070383) DODGE轴承 P4B-S2-211RE (070385) DODGE轴承 P4B-S2-215RE (070386) DODGE轴承 P4B-S2-300RE (070387) DODGE轴承 P4B-S2-307RE (070389) DODGE轴承 P4B-S2-315RE (070391) DODGE轴承 P4B-S2-407RE(070393) DODGE轴承 P4B-S2-415RE (070395) DODGE轴承 P4B-S2-115L (070397) DODGE轴承 P4B-S2-200L (070398) DODGE轴承 P4B-S2-203L (070399) DODGE轴承 P4B-S2-207L (070401) DODGE轴承 P4B-S2-211L (070403) DODGE轴承 P4B-S2-215L (070404) DODGE轴承 P4B-S2-300L (070405) DODGE轴承 P4B-S2-307L (070407) DODGE轴承 P4B-S2-315L (070409) DODGE轴承 P4B-S2-407L (070411) DODGE轴承 P4B-S2-415L (070413) DODGE轴承 P4B-S2-115LE (070415) DODGE轴承 P4B-S2-200LE (070416) DODGE轴承 P4B-S2-203LE (070417) DODGE轴承 P4B-S2-207LE (070419) DODGE轴承 P4B-S2-211LE (070421) DODGE轴承 P4B-S2-215LE (070422) DODGE轴承 P4B-S2-300LE (070423) DODGE轴承 P4B-S2-307LE (070425) DODGE轴承 P4B-S2-315LE (070427) DODGE轴承 P4B-S2-407LE(070429) DODGE轴承 P4B-S2-415LE (070431)
DODGE轴承 EP4B-S2-207R (070433) DODGE
轴承EP4B-S2-211R (070434) DODGE轴承 EP4B-S2-215R(070435) DODGE轴承 EP4B-S2-300R (070436) DODGE轴承 EP4B-S2-307R (070437) DODGE轴承
EP4B-S2-315R (070438)
:新余广柴服务为保证开启压力值准确，应使调整时的介质条件，如介质种类、温度等尽可能接近实际运行条件。介质种类改变，特别是当介质聚积态不同时（从液相变为气相），开启压力常有所变化。工作温度升高时，开启压力一般有所降低。故在常温下调整而用于高温时，常温下的整定压力值应略高于的开启压力值。高到什么程度与阀门结构和材质选用都有关系，应以制造厂的说明为根据。常规安全阀用于固定附加背压的场合，当在检验后调整开启压力时（此时背压为大气压），其整定值应为的开启压力值减去附加背压值。